New: ASCloud, our paperless food safety system. Full document FSMS from R3,800 a month, R638 plans from R499. See pricing

Heat Stress in Food Factories: The New Physical Agents Rules

Since the Environmental Regulations for Workplaces, 1987, fell away in September 2026, heat stress at South African workplaces has been governed only by the Physical Agents Regulations, 2024, made by the Department of Employment and Labour under the Occupational Health and Safety Act 85 of 1993. They set an action level of 27 °C and an occupational exposure limit of 30 °C, both measured as wet bulb globe temperature (WBGT) averaged over one hour. A bakery oven line, a fryer bank or a retort hall in December can exceed both.

The new regulations were published on 6 March 2025 and repealed the 1987 rules 18 months later. A food business now needs a documented physical agent exposure risk assessment by a competent person, monitoring to SANS 7243 where that assessment shows the limit could be reached and, where it is reached, a set of controls that includes acclimatisation, drinking water at the place of work and heat specific first aid.

Drinking water and protective clothing are where food hygiene rules and the heat rules pull against each other, and most sites will have to change something there. If the person who writes your risk assessments has not worked with the new regulations, our HIRA and incident investigation course covers physical agent assessments in Module 3. It takes about 5 hours online and costs R1,495.

In short

  • The heat stress action level is WBGT 27 °C and the exposure limit is WBGT 30 °C, both averaged over one hour (Table 1).
  • Cold stress in freezers is assessed as equivalent chill temperature. Between minus 18 °C and minus 34 °C, continuous exposure is capped at 50 minutes in each hour, followed by at least 10 minutes somewhere warm. Colder bands are stricter.
  • The exposure risk assessment is documented, done by a competent person and repeated at least every 24 months. Records are kept for 40 years.
  • At or above the limit the employer must, among other things, run a heat acclimatisation programme and provide enough drinking water at the place of work.
  • Food hygiene rules on eating and drinking in production areas still apply, so water has to be planned into the layout and the break schedule.

What do the Physical Agents Regulations require for heat?

Regulation 10 starts with elimination. The employer must remove heat stress at source where that is reasonably practicable, for example by insulating an oven, ducting heat away from a fryer or moving a packing table out of the path of a proofer’s exhaust.

Where exposure reaches the action level of WBGT 27 °C, the employer must find out why and review the controls so that the limit is not reached. At or above the limit of WBGT 30 °C, the minimum list is longer. The table sets out what that means on a food production floor.

Regulation 10(3) dutyWhat it looks like in a food business
Alternative working methods and limits on duration and exposureRotate staff between the oven face and cooler tasks, schedule the hottest jobs for the early shift, use a work and rest schedule
Plant designed to reduce heat, and maintenanceExtraction hoods that work, spot cooling at fixed workstations, and oven and proofer insulation kept in repair
Review of workplace layout and rest facilitiesA cool rest area near the line, out of the production zone but close enough to use
Review of the risk assessment, monitoring and medical programmesA fresh assessment when the season changes, or when a new product changes oven temperature, fryer load or line speed
Heat acclimatisation programmeNew starters, staff back from leave and staff moved from the cold store build up their time near the heat over several days
Prompt first aid specific to heatFirst aiders trained to tell heat exhaustion from heat stroke, with cooling and a way to call an ambulance at once
Sufficient potable water at the place of workDrinking water stations at the zone boundary, sized by the risk assessment
Protective clothing that allows for its heat loadClothing adjustment values from Table 9 are added to the measured WBGT. A long sleeved vapour barrier apron over cloth coveralls adds 4, so a reading of 27 °C counts as 31 °C

Monitoring has to follow SANS 7243, be done by a competent person with instruments calibrated to a traceable standard, and the regulations’ general duties apply as well. Employees exposed to a physical agent must be trained before exposure, with refreshers at least once a year, and the health and safety representatives must be consulted. Medical screening is required where the risk assessment shows a need, and for vulnerable employees an occupational medicine practitioner advises whether it is needed.

How do you measure heat stress in a bakery or kitchen?

WBGT combines air temperature and humidity with air movement and radiant heat in one figure, which is why a humid fryer room can be more dangerous than a dry oven hall at the same air temperature. Indoors and out of the sun, WBGT is 0.7 times the natural wet bulb temperature plus 0.3 times the globe temperature. Outdoors in sunlight, such as an open dock, it is 0.7 times natural wet bulb plus 0.2 times globe plus 0.1 times air temperature.

A wall thermometer is not a WBGT reading. The measurement needs a WBGT meter or heat stress monitor, placed where people actually work and taken during the hottest part of the shift in the hottest part of the year. In most of South Africa that means December to February, in the afternoon, with the ovens at full load.

The regulations set one limit for everybody, but work rate still matters when you choose controls. The US National Institute for Occupational Safety and Health (NIOSH) recommends lower WBGT limits for heavy work than for light work, and for people who are not yet acclimatised. A baker loading racks into a rack oven is doing heavier work than a packer at a cooled table, and the assessment should say so. There is no published South African figure for heat illness in food factories, so the controls here lean on the regulations and on NIOSH guidance.

A worked example for a Gauteng plant bakery

Take a plant bakery in Ekurhuleni with two tunnel ovens. The figures are illustrative. In mid December a competent person takes WBGT readings over the afternoon shift at four workstations and averages each over the hottest hour.

WorkstationOne hour WBGTAction
Oven infeed and burner side, tunnel oven 131.2 °C, above the 30 °C limitRegulation 10(3) controls now: refit the missing side panel and rotate staff off the oven every 30 minutes
Depanning and racking28.4 °C, above the 27 °C action levelFind the cause (a failed extraction fan) and fix it before it reaches 30 °C
Wrapping and slicing25.9 °C, below the action levelKeep monitoring through the season
Dispatch dock, afternoon27.6 °C, above the action levelShade over the dock door, load the afternoon trucks earlier

The fixes in this example are engineering first. Suppose the extraction fan over depanning failed in October and sits on the maintenance list as a comfort item, not a health and safety item. Suppose a side insulation panel on tunnel oven 1 was left off after a burner repair, and the radiant heat shows in the globe reading. Neither costs much to fix, and both would move the readings.

Because the December roster brings in seasonal staff, the assessment should also set an acclimatisation rule. NIOSH advises that a new worker spends no more than 20 percent of the usual time in the heat on the first day, increasing by no more than 20 percent a day, and that experienced workers coming back from leave build up over about four days. The regulations do not set the schedule, so record the one you choose and why.

Every reading, the assessment, the action plan and the training records go into the file and stay there for 40 years. Our earlier article on hazard identification and risk assessment in a food factory sets out the method, and Lesson 3.2 of our HIRA course works through heat, cold and noise assessments on a case study food business, for R1,495 a person.

Where food hygiene rules and heat rules clash

This is where food businesses get stuck. The heat regulations say drinking water must be available at the place of work. Food hygiene rules and every certification scheme keep food and drink out of production areas, because a bottle on a packing table is a contamination risk and a source of hard plastic or glass.

The answer is to plan the water rather than ban it. Put drinking stations at the boundary of the production zone, on the change room side of the hand wash and hygiene barrier, with single use paper cups or named, lidded bottles that stay at the station. Staff then wash their hands again on the way back to the line.

Build drink breaks into the shift so people do not have to ask. NIOSH suggests about one cup, roughly 250 ml, every 15 to 20 minutes during moderate work in the heat, and no more than about 1.4 litres an hour. Where sweating goes on for more than two hours, it recommends drinks with electrolytes. The explanatory notes to the regulations make the basic point too: drink regularly through the shift, not only when thirsty.

Protective clothing raises the same tension. Hairnets and long sleeved coats stay, because they protect the food. Vapour barrier aprons in a wash bay add heat, so they belong in the assessment with their Table 9 value, and the wash bay may need its own rotation. A short PVC apron is not the same ensemble, so record what is actually worn.

Sweat is a hygiene hazard too. A worker wiping a forehead with a gloved hand over open product is a finding in any hygiene audit. Cooler workstations reduce both problems at once, which is a good argument to put in front of the person who signs the capital budget.

Cold rooms and blast freezers fall under the same rules

The same regulations cover cold stress, measured as equivalent chill temperature (ECT), which accounts for air movement as well as temperature. The limit is 10 °C over four hours, and Table 8 caps exposure as the chill gets worse. Between minus 18 °C and minus 34 °C ECT, continuous exposure is limited to 50 minutes in each hour, followed by at least 10 minutes, under supervision, somewhere comfortably warm. Below minus 34 °C, exposure is limited to two periods of 30 minutes, at least four hours apart, and below minus 57 °C to 5 minutes in any eight hours.

A picker in a minus 25 °C freezer is close to minus 25 °C ECT in still air. With the evaporator fans moving air at 3 metres a second, the formula in the explanatory notes puts it at about minus 32 °C, and from about 3.4 metres a second it drops below minus 34 °C. Measure air speed at the picking face, not only the room temperature. In a blast freezer at minus 35 °C or colder with the fans running, ECT can fall below minus 57 °C, so measure before anyone works inside.

Cold measurements must be taken over at least four hours, in the coldest part of the shift and the coldest quarter of the year, and the assessment needs dry, insulated whole body clothing, a timed rotation and a warm area.

Where ISO 45001 fits

ISO 45001:2018 asks for hazard identification and risk assessment that consider the working environment, and for controls chosen in order from elimination down to protective equipment. A site certified to ISO 45001 should already have heat and cold on its hazard register. What changed is the yardstick: the register now has to use the Table 1 limits and the 24 month review cycle.

The 2024 amendment to ISO 45001 also requires an organisation to decide whether climate change is a relevant issue for its management system. For a bakery in Polokwane or a packhouse in the Northern Cape, hotter summers are a fair answer, and heat stress is where that decision shows up on the floor. ISO 45001:2018 with that amendment is the edition certified today, and a revised edition is at draft stage. If you run an integrated system, our guide to combining ISO 9001, 14001 and 45001 with food safety shows where the overlaps sit.

At ASC Food Safety Consultants we train the people who write these assessments and audit the systems they sit in. The HIRA course prepares the person who writes and reviews the risk assessment. It does not on its own make someone a competent person under the regulations, and WBGT monitoring itself must be done by a competent person qualified in heat stress with a calibrated instrument, usually an occupational hygienist.

Why food businesses choose ASC

Rated 4.9 out of 5 from more than 400 Google reviews across our three offices.

Gqeberha Google reviews Johannesburg Google reviews Cape Town Google reviews

Our online courses hold a 4.9 average from 2,622 course reviews and more than 7,200 course enrolments.

ISO 9001 certified
SAATCA registered online training course provider (TC 065)
FoodBev SETA Accredited Provider No. 587/00337/1900
Exemplar Global Recognised Training Provider

Train your risk assessor

Hazard Identification, Risk Assessment and Incident Investigation (FS67)

About 5 hours online and self paced. You review a 212 line baseline risk assessment for a case study food business, then work through chemical, ergonomic and physical agent assessments, heat and cold among them, in the HIRA Register and Incident Investigation tools. Set the course fee against a prohibition notice from a Department of Employment and Labour inspector, or a heat stroke case on your December roster. R1,495 per person.

Enrol on the HIRA course WhatsApp us for a team quote

Need the full set for your health and safety team? OHS Act Compliance Courses Bundle (four courses for R3,066 instead of R4,380).

Questions we are often asked

Are the Environmental Regulations for Workplaces, 1987 still in force?

No. Regulation 21 of the Physical Agents Regulations, 2024 repealed them 18 months after the new regulations were published on 6 March 2025, which brought them to an end in September 2026. Heat and cold, lighting and indoor air quality now fall under the Physical Agents Regulations.

The occupational exposure limit is a WBGT of 30 °C averaged over one hour, with an action level of 27 °C. At the action level the employer must find the cause and review controls. At the limit the full list of regulation 10(3) controls applies.

Can staff drink water in a food production area?

Hygiene rules keep food and drink out of production areas, but the heat regulations require drinking water at the place of work. Most sites solve this with drinking stations at the edge of the production zone and scheduled drink breaks, both written into the risk assessment.

Can ASC help with our heat stress assessment?

ASC trains the people who carry out these assessments and audits the management systems they belong to. Enrol on the HIRA course or WhatsApp us on +27 61 483 0381 to talk about your site.

Sources

  1. Department of Employment and Labour, Physical Agents Regulations, 2024, GN 5952, Government Gazette No. 52226, 6 March 2025, regulations 3, 6, 7, 8, 9, 10, 18 and 21, Tables 1, 8 and 9 and the explanatory notes
  2. Department of Employment and Labour, Amendment of the Physical Agents Regulations, GN 7149, Government Gazette No. 54177, 20 February 2026
  3. Occupational Health and Safety Act 85 of 1993, sections 8 and 13
  4. NIOSH, Heat stress recommendations and Criteria for a Recommended Standard: Occupational Exposure to Heat and Hot Environments, publication 2016-106
  5. ISO 45001:2018, Occupational health and safety management systems, with Amendment 1:2024 (climate action changes), and ISO/TC 283 news on the revision
  6. SANS 7243, Ergonomics of the thermal environment, assessment of heat stress using the WBGT index

Leave a Comment

I accept the Terms and Conditions and the Privacy Policy

Exemplar Global Recognised Training Provider (RTP) badge issued to ASC Food Safety
International recognitionExemplar Global Recognised Training Provider (RTP)Exemplar Global, the international organisation that certifies auditors and recognises training providers, recognises 28 of our auditor, HACCP, GMP and ISO courses, including four lead auditor courses, whether we deliver them in class, in live virtual classes or online.
News & updates 5 new
4.9/5 what do you need today?